[PDF] Top 20 The effect of ageing process on three-point bending strength and permeability of 3D printed sand molds
Has 10000 "The effect of ageing process on three-point bending strength and permeability of 3D printed sand molds" found on our website. Below are the top 20 most common "The effect of ageing process on three-point bending strength and permeability of 3D printed sand molds".
The effect of ageing process on three-point bending strength and permeability of 3D printed sand molds
... The printed specimens were then taken out of the job box and ...During the process of de-powdering, the unbounded sand particles were removed using ... Voir le document complet
27
Investigation of process parameter effect on anisotropic properties of 3D printed sand molds
... ABSTRACT The development of sand mold three-dimensional printing technologies enables the manufacturing of molds without the use of a physical ...However, ... Voir le document complet
28
Experimental and numerical characterization of functional properties of sand molds produced by additive manufacturing (3D printing by jet binding) in a fast foundr
... manufactured sand molds and cores for metal casting are being progressively replaced by additively processed sand molds in aerospace/automotive industry, facilitating the ... Voir le document complet
216
Characterisation of 3D printed sand moulds using micro-focus X-ray computed tomography
... by the authors, in relation to the three-point bending (3DP) strength and permeability; hence, this paper contains only a short and concise literature ... Voir le document complet
14
The Effect of Adversity on Process Innovations
... regardless of production cost ...compare the changes in two outcomes – the introduction of process in- novation and the provision of managerial incentives – between ... Voir le document complet
44
Effect of reproductive ageing on pregnant mouse uterus and cervix
... gestation and labour in parallel with altered progesterone withdrawal, we determined how this impacted on reproductive tissues and mechanisms underpinning the observed age-related phenotypic ...those ... Voir le document complet
45
Experimental determination of GFRC tensile parameters from three-point bending tests using an analytical damage model
... shows the comparison of the load–displacement exper- imental results of mean curves obtained above ( ...) and the ana- lytical model after the adjustment ...that ... Voir le document complet
15
Modeling the injection of textured molds
... micro-optic and micro-mechanics due to its ef- fectiveness for mass ...model the injection of textured molds. Such tools can predict the different filling scenarios of the ... Voir le document complet
6
Effect of ageing on the properties of the W-containing IRIS-TiAl alloy
... °C and 700 °C, which was attributed to the dissolution of the 2 ...In the author’s opinion, the interpretation of these ageing effects requires deep understanding ... Voir le document complet
23
Comparison of the strength of iceberg and other freshwater ice and the effect of temperature
... reflects the colder air temperatures at the time of his measurements, which were carried out between March and May 1984 at the northern end of Baffin ...Island. The other ... Voir le document complet
21
Effect of strength and fiber reinforcement on fire resistance of high-strength concrete columns
... HSC and NSC at elevated ...regarding the occurrence of explosive spalling when HSC is subjected to rapid heating, as in the case of a fire (Diederichs et ...Council of Canada ... Voir le document complet
14
The effect of mixing time on the compressive strength of masonry mortars
... Archives des publications du CNRC This publication could be one of several versions: author’s original, accepted manuscript or the publisher’s version. / La version de cette publication peut être l’une des ... Voir le document complet
14
The effect of pore geomatry on In vitro extracellular matrix formation in 3D-printed calcium phosphate-based scaffolds
... THE EFFECT OF PORE GEOMETRY ON IN VITRO EXTRACELLULAR MATRIX FORMATION IN 3D-PRINTED CALCIUM PHOSPHATE-BASED SCAFFOLDS Ehsan Sadeghian Dehkord 1 , Bingbing Liang 1 , Liesbet Geris 1, ... Voir le document complet
1
Effect of the sand-blasting of edge peeling tools on the cutting forces and wear resistance
... Science Arts & Métiers (SAM) is an open access repository that collects the work of Arts et Métiers Institute of Technology researchers and makes it freely available over the web ... Voir le document complet
5
Temperature dependence of methanol and tensile strength of insulation paper: Kinetics of the changes of mechanical properties during ageing
... under the LODP (levelling-off degree of poly- merization) of the ...papers. The LODP corresponds to the average length of the crystalline region of ... Voir le document complet
9
Clustering and the Three-Point Function
... example of such phenomena in the context of the AdS/CFT correspondence; namely the emergence of the classical string world- sheet from the three-point ... Voir le document complet
79
Effect of end connection restraints on the stability of steel beams in bending
... plane bending, Uniform torsion, Warping ...under the action of bending loads in the plane of maximum flexural rigidity can buckle by combined twist and lateral ... Voir le document complet
19
Effect of membrane permeability on survival of hemodialysis patients
... for the Membrane Permeability Outcome (MPO) Study Group *Department of Nephrology, Dialysis and Renal Transplantation, ...Department of Nephrology, University Hospital Reina Sofia, ... Voir le document complet
10
Experimental and statistical study of three adherence tests for an epoxy-amine/aluminum alloy system: Pull-Off, Single Lap Joint and Three-Point Bending tests
... T The mechanical resistance of a bonded joint depends on the adhesive interaction onto the substrate and the mechanical properties of the adhesive ...measuring ... Voir le document complet
10
The Effect of sand/cement ratio and silica fume on the microstructure of mortars
... one of several versions: author’s original, accepted manuscript or the publisher’s ...For the publisher’s version, please access the DOI link ... Voir le document complet
13
Sujets connexes