Experimental and numerical analysis
Experimental and numerical analysis of corrosion-induced cover cracking in reinforced concrete sample
... efficiency and the relevancy of the post-treatment technique used in this ...4. Numerical identification of the local failure mechanisms ...Continuous analysis The FE analysis lies in a ...
20
Deployment of a Neo-Hookean membrane: experimental and numerical analysis
... interface and material boundaries; the main limitation of this formulation is the mesh distortion for large deformations and moving structures because the fluid is solved on a moving domain due to the ...
12
Pharmaceutical powders compaction: Experimental and numerical analysis of the density distribution
... dies. Experimental results of the compaction of microcrystalline cellulose are compared to those predicted with an analytical model and with numerical ...Walker analysis coupled with the ...
8
Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks
... paper, experimental study on drilling of multi-material made of CFRP laminate with aluminium plate has been carried ...feed and lip length of the double cone drill on cutting forces and quality of ...
12
Experimental and numerical analysis of behavior of honeycomb sandwiches panels subjected to impact.
... panels and their internal buckling, undetectable by a visual inspection, has been carried out by ka XCT ...(static and dynamic) and to estimate the critical buckling load at each ...the ...
190
Thermal fatigue analysis of automotive Diesel piston: Experimental procedure and numerical protocol
... transient analysis corresponding to the heating and cooling phases of an engine bench test is performed and repeated for 3 cycles until the thermal map get ...c, experimental thermal evolution ...
11
Failure analysis of composite bolted joints by an experimental and numerical approach
... Failure analysis of composite bolted joints by an experimental and numerical approach Benoît Montagne, Frederic Lachaud, Eric Paroissien, Dominique Martini.. To cite this version: Benoît[r] ...
3
Numerical and experimental analysis of a solid oxide fuel cell stack
... Access and use of this website and the material on it are subject to the Terms and Conditions set forth at Numerical and experimental analysis of a solid oxide fuel cell ...
2
Experimental and Numerical Analysis of Gas/Powder Flow for Different LMD Nozzles
... above and below the focal plan, which differs from the nozzle’s ...] and showed that the powder flow keeps pitot ian distribution within a +/− 2 mm distance to the focal ...these experimental studies ...
21
Experimental and numerical analysis of building boundary conditions
... Several thermal balance models have been developed over recent years, particularly for building applications concerning dwellings equipped with ordinary-sized windows. These thermal balance applications are generally ...
19
Experimental and numerical analysis of unfolding failure of L-shaped CFRP specimens
... bars and support bars to minimize the out-of-plane shear stress and maximize the out-of-plane tensile stress as shown in ...radius and the out-of-plane tensile stress was maximal at approximately one ...
29
Compensatory uptake functions in empirical macroscopic root water uptake models: experimental and numerical analysis
... (08) and RF (11), but slightly overestimated θ in deep soil layers in RF ...Cst and β Inv resulted in significantly higher and lower θ values in upper and lower soil layers, ...(11) and ...
57
Multi-level experimental and numerical analysis of composite stiffener debonding. Part 2: Element and panel level
... presented and validated by the 7-point bending test was applied to both cases (Figure ...hypothesis and thus avoid the boundary conditions at the edges of the local model perturbing the results, pieces of ...
32
Experimental and numerical analysis of Carbon Fiber Reinforced Polymer notched coupons under tensile loading
... They showed that the strength of notched composite laminates decreased when the notch size increased and concluded that the hole size effect was triggered by the presence of non-critical[r] ...
15
Experimental and numerical analysis of localization during sequential test for an IF-Ti steel
... There are indeed simpler models, such as self-con- sistent models, which can be used for the study of localization. To our knowledge, however, they have not been applied to sequential loading paths with the appearance of ...
13
Experimental and numerical analysis of Carbon Fiber Reinforced Polymer notched coupons under tensile loading
... They showed that the strength of notched composite laminates decreased when the notch size increased and concluded that the hole size effect was triggered by the presence of non-critical[r] ...
14
Experimental and numerical analysis of unfolding failure of L-shaped CFRP specimens
... good restitution of effort, as mentioned in the ASTM standard [51] . 4.2. Modelling the in fluence of intralaminar matrix cracking The influence of an intralaminar matrix crack depended on the stacking sequence as shown in ...
14
Experimental and numerical analysis of nonlinear properties of rail fastening systems
... dependent and amplitude dependent properties of rail fastening systems, the experimental results are simulated by three different numerical ...models. Numerical models were commonly used to ...
217
EXPERIMENTAL STUDY AND NUMERICAL ANALYSIS OF CRACK OPENING IN CONCRETE
... elements and also to validate constitutive models. Displacement and deformation measurements are typically measured by displacement transducers or strain ...precision and reliability (under certain ...
152
Numerical and experimental analysis of residual stress and plastic strain distributions in machined stainless steel
... zones and friction between the tool and the workpiece ( ...) and to workpiece (Q W ) in proportions depending on tool and material properties and cutting ...low and leads to a ...
13