[PDF] Top 20 C-S-H/polyaniline nanocomposites prepared by in situ polymerization
Has 10000 "C-S-H/polyaniline nanocomposites prepared by in situ polymerization" found on our website. Below are the top 20 most common "C-S-H/polyaniline nanocomposites prepared by in situ polymerization".
C-S-H/polyaniline nanocomposites prepared by in situ polymerization
... the in situ polymerization technique is ...subsequent polymerization more effective. Polyaniline (PAn) was chosen as the organic ...polymerized by introducing an oxidant to the ... Voir le document complet
35
Copper and iron based thin film nanocomposites prepared by radio frequency sputtering. Part I: elaboration and characterization of metal/oxide thin film nanocomposites using controlled in situ reduction process
... performed by grazing incidence X-ray diffraction (GIXRD) (grazing angle a = 1°) using a Siemens D5000 diffractometer with the copper Ka radiation (k = ...determined by electron probe micro-analysis (EPMA) ... Voir le document complet
10
Copper and iron based thin film nanocomposites prepared by radio-frequency sputtering. Part II: elaboration and characterization of oxide/oxide thin film nanocomposites using controlled ex-situ oxidation process
... reported in Table 4 ...low in the HL for all the samples. In the SL, the void fraction is more important and increases for the films deposited at low P 9 d product, ...content in the ... Voir le document complet
13
Copper and iron based thin film nanocomposites prepared by radio-frequency sputtering. Part II: elaboration and characterization of oxide/oxide thin film nanocomposites using controlled ex-situ oxidation process
... shown in Fig. 5 b. The total etching time required to reveal silicon in the substrate is attributed to the total thicknesses of the ...structure in two layers which is con- sistent with the FE-SEM ... Voir le document complet
12
Polymer/layered silicate nanocomposites by combined intercalative polymerization and melt intercalation: a masterbatch process
... PCL-based nanocomposites prepared from the masterbatches M1–M3 (Table ...Intercalated nanocomposites were collected as supported by the significant increase in the interlayer distance ... Voir le document complet
11
Poly(epsilon-caprolactone)/clay nanocomposites prepared by melt intercalation: mechanical, thermal and rheological properties
... particularly in case of G′ but the moduli increase dramatically at low ...for nanocomposites of, ...PCL nanocomposites were first reported by Krishnamoorti [22] and Giannelis [23] in ... Voir le document complet
9
Innovative Vascular Prostheses Combining 3D Electrospun Nanofiber Matrices and Bioactive Coatings Prepared by Plasma-Polymerization
... enhancing in situ ...the in vitro and in situ endothelialization process, growth factors (GFs) such as vascular endothelial growth factor (VEGF) and basic fibroblast growth factor ... Voir le document complet
181
Ability of nitrones of various structures to control the radical polymerization of styrene mediated by in situ formed nitroxides
... radical polymerization of styrene using the nitrone/AIBN system in the automated synthesizer (styrene/nitrone: 45/1 and nitrone/AIBN: ...argon by glass syringes with stainless steel capillaries ... Voir le document complet
15
Electrical conductive double-walled carbon nanotubes � Silica glass nanocomposites prepared by the sol�gel process and spark plasma sintering
... nanotubes; Nanocomposites; Silica; Spark plasma sintering; Electrical conductivity The outstanding electrical, thermal and mechan- ical properties of carbon nanotubes (CNTs) have broad- ened the research into ... Voir le document complet
5
Recent advances in layered double hydroxide /polymer latexes nanocomposites: from assembly to in situ formation.
... easily prepared in a large quantity and organically ...g by varying the proportion of trivalent metal ...swelling in water but does not hamper exfoliation under specific conditions, especially ... Voir le document complet
50
Aligned carbon nanotubes in ceramic-matrix nanocomposites prepared by high-temperature extrusion
... powders by ZrO 2 particles about 1 lm in size. In a second step, the oxide powders were reduced in a H 2 –CH 4 atmosphere (18 mol% CH 4 , maximum temperature 1050 ...nanometers ... Voir le document complet
7
Carbon nanotubes prepared in situ in a cellular ceramic by the gelcasting-foam method
... used in the preparation process of dense ceramics. 19,20 In this method, a foam is created in an aqueous sus- pension of ceramic powder by a vigorous mechanical stirring and is stabilised ... Voir le document complet
11
Aligned carbon nanotubes in ceramic-matrix nanocomposites prepared by high-temperature extrusion
... powders by ZrO 2 particles about 1 lm in size. In a second step, the oxide powders were reduced in a H 2 –CH 4 atmosphere (18 mol% CH 4 , maximum temperature 1050 ...nanometers ... Voir le document complet
8
ZnO-based varistors prepared by spark plasma sintering
... was prepared by dissolving antimony chloride in 4 M hydrochloric ...9.3 by adding ...calcinated in ambient atmosphere at 500 ◦ C for 1 h in static ... Voir le document complet
12
Synthesis of single-walled carbon nanotubes using binary (Fe, Co, Ni) alloy nanoparticles prepared in situ by the reduction of oxide solid solutions
... particles shows very few nanotubes mainly because the nanotubes and their bundles are considerably smaller than 10 nm in diameter. The presence of large quantities of single-walled nanotubes in the case of ... Voir le document complet
8
Synthesis of single-walled carbon nanotubes using binary (Fe, Co, Ni) alloy nanoparticles prepared in situ by the reduction of oxide solid solutions
... the oxide support affords a good distribution of the alloy nanoparticles on its surface. Alloying promotes the decomposition of CH to produce carbon nan- 4 otubes, the quality of which depends on the alloy composition. ... Voir le document complet
9
Recent developments in anionic polymerization
... circumvented in some cases [40**]. The selected general strategy is illustrated in Figure 4 which basically consists of the nucleophilic attack (by an initiator or a living growing chain) of a ... Voir le document complet
11
Rare-earths doped-nanoparticles prepared by pulsed laser ablation in liquids
... produced in faster and cleaner ways, even if sometimes the compounds quantity is at a lim- ited ...replaced by bulk materials obtained by solid state reaction, so PLAL could be considered as a ... Voir le document complet
11
σ-H–H, σ-C–H, and σ-Si–H Bond Activation Catalyzed by Metal Nanoparticles
... dispersed in solution were used in the hydrosilylation of ...synthesized by decomposition of Pt(dba) 2 or Karstedt’s complex in presence of n-octylsilane or polymethylhydrosiloxane (PMHS) ... Voir le document complet
96
Tailor-made polymers by organometallic-mediated radical polymerization (OMRP)
... radical polymerization (CRP) techniques appeared as major achievements because it paved the way to the synthesis of precise macromolecular architectures under mild experimental ... Voir le document complet
1
Sujets connexes