Fabrication process
Chemically resistant encapsulant to enable a novel MEMS fabrication process
... MEMS fabrication process flow. The novel MEMS fabrication process flow can be shortly described as a “packaging first, MEMS release second”, whereas a standard process starts form MEMS ...
5
Evolution of chemical and thermal curvatures in thermoset-laminated composite plates during the fabrication process
... Abstract Residual deformations and stresses formation in the thermoset-laminated composite is a frequently studied subject in the recent years. During fabrication, the laminated composites undergo chemical ...
14
A fabrication process for self-connected horizontal SiGe nanowires
... the fabrication process in the upper layers circuitry must be below 550 °C [6] in order to preserve the performances of the devices in the front-end of the line ...the fabrication of ...
12
Direct laser fabrication process with coaxial powder projection of 316L steel. Geometrical characteristics and microstructure characterization of wall structures
... the process parameters: laser speed V and vertical laser shift ...the process parameters. In order to find the best parameters, the fabrication time is taken into ...
7
Wafer-level fabrication process for fully encapsulated micro-supercapacitors with high specific energy
... 257 mJ cm -2 on a 2.5 V potential range could be achieved, which is 5.7 times more than the best previously reported performance for carbon-based micro-EDLC by Shen et al. ( 2011 ). In order to provide a fully ...
8
A fabrication process for emerging nanoelectronic devices based on oxide tunnel junctions
... In traditional RRAM, a resistance switching cell is a vertical two-terminal device, consisting of two electrodes, which sandwiches a resistance switching material. The first electrode is patterned, the switching ...
9
Control of carbon nanotube stiffness via tunable fabrication process parameters that determine CNT geometry
... Again, only the outside diameter and wall thickness are independent parameters because the elastic modulus is a material property, the length of the CNT is set by the [r] ...
126
Study of the impact of variations of fabrication process on digital circuits
... 6.3 Cell level analysis Mismatch simulation for different buffers and inverters revealed a decreasing σ with drive strength as shown in Figure 6-4. σ-values (as percentage of normalized SS delay) are plotted against ...
210
Si and SiGe Nanowires: Fabrication Process and Thermal Conductivity Measurement by 3ω-Scanning Thermal Microscopy
... In this paper, we first recall, in Section 2, the principle of the measurement setup as well as the experimental conditions. Then, we present results obtained on NWs obtained by two di fferent growing processes. The first ...
11
One-step fabrication process of superhydrophobic green coatings
... Fig. 4. EDX spectra of silver films prepared in (a) silver nitrate solution and (b) silver nitrate solution with benzoic acid molecules. Inset shows the FTIR spectra of silver powder collected from the silver films ...
13
A generic process modelling – LCA approach for UF membrane fabrication: Application to cellulose acetate membranes
... generic process modeling – LCA approach for UF membrane fabrication: Application to cellulose acetate membranes” [1] , a generic model is described and used to obtain the list of material and energy flows as ...
35
Fabrication of gas electrodes by wet powder spraying of binder-free particle suspensions using a pulse injection process
... the fabrication process for gas electrodes on electrolyte substrates, a wet powder spraying process was de- vised to apply a pulse injection of a binder-free suspension com- posed of very fine ...
6
A generic process modelling – LCA approach for UF membrane fabrication: Application to cellulose acetate membranes
... membrane fabrication otherwise than by considering module materials (see Table 1 ), it is difficult to compare the exhaustive inventory in Table 3 to other inventories in the ...industrial fabrication data ...
13
Pillars fabrication by DSA lithography: material and process options
... pillars fabrication process using PS-cylinder-forming PS-b-PMMA ...The process conditions were optimized in terms of BCP self-assembly annealing temperature/time, brush layer composition and PMMA ...
8
MEMS inertial sensors design and fabrication based on an innovative process
... the fabrication process, the overlap was set equal to 2 µm for the following reasons: (1) it has to be greater than the gap in order to ensure a comb-like shape (2) this way, it is equal to the vertical ...
138
LA FABRICATION DES SIGNAUX
... bien fabrication : la technique, ici, inclut (exploite ?) le savoir (nous aurons à analyser leurs rapports), mais l’analyse technique n’en est pas pour autant ...
10
de la fabrication des compétences
... L’archive ouverte pluridisciplinaire HAL, est destinée au dépôt et à la diffusion de documents scientifiques de niveau recherche, publiés ou non, émanant des établissements d’enseignemen[r] ...
16
Influence of process parameters on thermal and mechanical properties of polylactic acid fabricated by fused filament fabrication
... of process parameters on thermal and mechani- cal properties of PLA in FFF ...cooling process and formation of adjacent ...that process parameters have a signifi- cant impact on the mechanical ...
11
A New Process for the Fabrication of SiC Power Devices and Systems on SiCOI (Silicon Carbide On Insulator) Substrates
... process, is a promising substrate for power applications, providing the excellent breakdown field and thermal conductivity of 4H-SiC, on ...the fabrication of power ...full fabrication of the ...
7
Numerical simulation of a thermoviscoelastic frictional problem with application to the hot embossing process for microstructure fabrication
... / La version de cette publication peut être l’une des suivantes : la version prépublication de l’auteur, la version acceptée du manuscrit ou la version de l’éditeur. Access and use of [r] ...
5