AFTER UNPACKING THE APPLIANCE, MAKE SURE IT IS NOT DAMAGED. IN CASE OF DOUBT, DO NOT USE THE APPLIANCE AND CONTACT YOUR SUPPLIER OR A QUALIFIED TECHNICIAN.
THE USE OF ACCESSORY AND ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURER MAY CAUSE INJURIES.
ALWAYS UNPLUG THE APPLIANCE IF NOT USING IT FOR A PERIOD OF TIME.
REMOVE ALL PACKAGING AND DO NOT LEAVE THE PACKAGING MATERIAL SUCH AS PLASTIC BAGS, POLYSTYRENE AND ELASTIC BANDS IN EASY REACH OF CHILDREN AS THEY MAY CAUSE SERIOUS INJURIES.
AFTER UNPACKING YOUR APPLIANCE, MAKE SURE YOU HAVE PUT IT ON A FLAT, STABLE AND HEAT-RESISTANT SURFACE. CHECK YOU HAD LEAVE ENOUGH SPACE BETWEEN YOUR APPLIANCE AND SURROUNDING WALL TO
ENGLISH
LET THE AIR CIRCULATE AROUND THE UNIT.
THERE SHOULD BE AT LEAST 50CM ON THE TOP AND 50CM ON SIDES APART FROM THE UNIT. DO NOT PUT ANYTHING INTO THE VENTILATION SLITS, OR OBSTRUCT THEM WITH FABRICS.
DO NOT USE YOUR UNIT OUTSIDE. DO NOT INSTALL IN FULL SUN OR IN A LOCAL WITH HIGH RISK OF FIRE. FOR YOUR OWN SAFETY, WE RECOMMEND YOU NEVER LEAVE THE APPLIANCE IN A PLACE THAT IS EXPOSED TO INCLEMENT WEATHER CONDITION.
THIS APPLIANCE MUST BE EARTHED. DO NOT USE AN EXTENSION LEAD.
CHECK THAT THE VOLTAGE MARKED ON THE RATING PLATE MATCHES TO YOUR LOCAL SUPPLY. IF NOT THE CASE, DO NOT USE THE APPLIANCE AND SEEK FOR EXPERT ADVICE.
DO NOT USE THIS APPLIANCE WITH A PROGRAMMER, TIMER OR SEPARATE REMOTE-CONTROL SYSTEM.
ENGLISH
TO AVOID OVERHEATING DO NOT COVER THE UNIT.
AVOID TO PLACE IT CLOSE TO ANY HEAT SOURCES, OBJECTS, GAS OR FLAMMABLE MATERIALS.
DO NOT PUT HEAVY OBJECTS ON THE APPLIANCE.
DO NOT PUT THIS APPLIANCE ON TOP OF OTHERS.
DO NOT INSERT YOUR FINGERS OR ANY OBJECTS THROUGH THE APPLIANCE’S GRID.
DO NOT INCLINE YOUR APPLIANCE MORE THAN 35° WHEN MOVING IT. AVOID ANY VIBRATIONS OR SHOCK. NEVER MOVE THE APPLIANCE WHEN IN USE.
CHILDREN SHALL NOT PLAY WITH THE APPLIANCE AND CLIMB ON THE APPLIANCE.
WHEN THE UNIT IS FUNCTIONING, KEEP AN EYE ON CHILDREN AND PETS.
DO NOT EXPOSE DOMESTIC ANIMALS OR PLANTS TO PROLONGED DIRECT AIR FLOW.
ENGLISH
NEVER USE PESTICIDES, OIL, DETERGENTS OR PAINTING SPRAY ON OR AROUND THE APPLIANCE.
TAKE ALL NECESSARY MEASURE WITH CORDS AND EXTENSIONS TO AVOID ANY INJURIES WHILE IN USE.
DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL. AVOID WATERS’ SPLASHING ON THE UNIT.
NEVER LEAVE APPLIANCE PLUGGED IN WHEN NOT IN USE.
NEVER IMMERSE IN WATER OR ANY OTHER LIQUID THIS APPLIANCE, ITS ELECTRIC PLUG AND CORD.
THE SUPPLY CORD SHOULD BE REGULARLY EXAMINED FOR SIGNS OF DAMAGE AND THE APPLIANCE IS NOT TO BE USED IF THE CORD IS DAMAGED.
NEVER PLUG THE APPLIANCE WITH WET HANDS.
ENGLISH
NEVER USE THE APPLIANCE WITH BARE OR WET FEET.
NEVER UNPLUG THE APPLIANCE BY PULLING THE POWER CABLE. ALWAYS UNPLUG THE APPLIANCE FROM THE MAINS SOCKET.
ALWAYS UNPLUG THE APPLIANCE BEFORE ANY CLEANING OPERATION.
STANDARDS
THIS APPLIANCE IS CONFORMED TO CURRENT DIRECTIVES AND STANDARDS.
ENGLISH
TABLE OF CONTENTS
DESCRIPTION ... 1
SET-UP AND USE ... 2 Assembling the appliance ... 2 Using your appliance ... 4
CLEANING AND MAINTENANCE ... 5 TECHNICAL INFORMATION ... 5
ENGLISH
1
DESCRIPTION
1) Front grid 2) Blade
3) Fixing nut for the back grid 4) Back grid
5) Motor shaft
6) Button for oscillation function 7) Fan body
8) Screws for fixing the base 9) Blade’s spinner
a. Turn the spinner clockwise to loosen b. Turn the spinner anti-clockwise to tighten 10) Base
11) Speed control buttons 12) Fan handle
ENGLISH
2
SET-UP AND USE
Assembling the appliance
Remove all packaging and do not leave the packaging material such as plastic bags, polystyrene and elastic bands in easy reach of children as they may cause serious injuries.
Take out all the parts of the appliance.
Follow below insctructions on how to assemble the fan:
Turn the fan body upside down (7). Ensure to stabilize your position to avoid damaging the motor head.
Insert the base onto the bottom of the fan body, ensure the holes of both bases are aligned. The part showing the rating plate shall face you.
. Insert each screw into each hole and tighten it with a screw driver until its blocking point.
Attention: Ensure to not over tightening the screws to avoid damaging the fan.
At the end of the operation, turn the fan back to its right position and place it on a stable and flat surface.
Before continuing your assembling, ensure that the fan body (7) is placed on a flat and stable surface. Unscrew by turning clockwise the nuts for the back grid and the spinner from the motor shaft. Take out the plastic tube protecting the shaft.
ENGLISH
3
Insert the back grid (4) onto the motor shaft (5) until its blocking point, ensure that the fan handle (12) is on the top of the grid. Check that the motor shaft is well centered inside the back grid.
Screw the fixing nut of the back grid (3) onto the motor shaft by turning it clockwise until its blocking point. To loosen the nut, turn it anti-clockwise.
Insert the blade (2) onto the motor shaft (5) and tighten the spinner (9) onto the motor shaft by turning it anti-clockwise. To loosen the spinner, turn it clockwise. Turn the blade on both side to ensure it’s well assembled.
ENGLISH
4
Place the front grid (1) opposing the back grid and ensure both are aligned. Clip the two grids by using the hooks located on the front grid. Turn the fan head up and down to ensure both grids are assembled.
Test of appliance before first use:
Push on the button 0 to ensure the fan is off. Plug in the appliance. Push on the button 1 to select slow speed and push on the oscillation function button (6), check that the fan works:
o Head of the fan turn without issues at regular speed.
o Fan blade turn without issues at regular speed.
At the end of your test, push on the button 0 to turn off the fan.
Using your appliance
Place your appliance on a flat, dry and stable surface with a 50 cm away from any walls and objects.
Plug your unit to a socket.
Adjust the fan head manually: hold firmly the fan craddle on one hand and on the other hand drag the fan grid upward or downward.
To adjust the speed, simply push the switch button located at the front of the appliance:
o 1: slow speed, o 2: medium speed, o 3: high speed.
o To stop your fan, push the button 0.
At the end of use, unplug the appliance.
WARNING: Do not put anything on the appliance, such as clothing or towels. Do not use the appliance in the bathroom or other wet areas.Do not insert your fingers or any objects through the appliance’s grid.
ENGLISH
5
CLEANING AND MAINTENANCE
The appliance needs only an external regular cleaning, the recommended cleaning frequency is once a month when used daily.
Unplug the appliance.
Always let the appliance to cool down for at least one hour before starting any cleaning operation.
When cleaning the outer part of the appliance, use a dry soft cloth (or sponge) or a damped one with neutral cleaner.
Do not use a hard brush or any others cleaners to avoid scratching the appliance.
To clean the accumulated dust inside the fan, use a vacuum cleaner with power at minimal.
TECHNICAL INFORMATION
Brand FAR
Reference VT40-17 CI
Power supply 220V-240V ~ 50Hz/60Hz
Power 60 W
Fan speed 3
Fan grid diameter 40 cm
WARNING: Always unplug your appliance before any cleaning operation. For safety reasons never pour water on your appliance for cleaning. Do not use toxic and corrosive products such as alcohol, industrial cleaners, solvents to clean the appliance as these may damage it.
VENTILATORE DA TAVOLO 40 cm
VT40-17 CI
ITALIANO