• Aucun résultat trouvé

One-step formation of stable multiple emulsions

N/A
N/A
Protected

Academic year: 2021

Partager "One-step formation of stable multiple emulsions"

Copied!
2
0
0

Texte intégral

(1)

HAL Id: cea-02341317

https://hal-cea.archives-ouvertes.fr/cea-02341317

Submitted on 31 Oct 2019

HAL is a multi-disciplinary open access

archive for the deposit and dissemination of sci-entific research documents, whether they are pub-lished or not. The documents may come from teaching and research institutions in France or abroad, or from public or private research centers.

L’archive ouverte pluridisciplinaire HAL, est destinée au dépôt et à la diffusion de documents scientifiques de niveau recherche, publiés ou non, émanant des établissements d’enseignement et de recherche français ou étrangers, des laboratoires publics ou privés.

One-step formation of stable multiple emulsions

P. Guenoun

To cite this version:

P. Guenoun. One-step formation of stable multiple emulsions. Bio-X Meeting, Jun 2017, Ashkelon, Israel. �cea-02341317�

(2)

One-step formation of stable multiple emulsions

P. Guenoun

(

patrick.guenoun@cea.fr

)

Université Paris-Saclay, LIONS, CEA Saclay

Stimuli-responsive multiple emulsions formed in a one-step mechanical emulsification process are shown to be stable for months. These emulsions are stabilized by amphiphilic copolymers synthesized by atom transfer radical polymerization (ATRP). Depending on pH, ionic strength and temperature, different emulsion types are obtained, including water-continuous (W/O/W) and oil-continuous (O/W/O) multiple emulsions.

In particular W/O/W emulsions can be formed with biocompatible molecules like poly(dimethylsiloxane)-b-poly(dimethylaminoethyl methacrylate) copolymer and Miglyol® 812 as an oil phase. These emulsions enable the encapsulation and controlled release of hydrophilic species with the three stimuli: pH, ionic strength and temperature.

Furthermore, we studied the formation conditions of multiple water – toluene – polystyrene-b-poly(styrene-st-dimethylaminoethyl methacrylate) emulsions. The conformation of the polymer adsorbed at the water – oil interface was probed using an original neutron reflectivity set-up. Our results evidence a correlation between emulsion type and polymer conformation. More precisely, the formation of multiple emulsions is promoted by a decrease in the curvature of the microemulsions formed in water, in agreement with cryo-transmission electron microscopy and small angle neutron scattering. Finally, we exhibit predictive criteria for the formation of multiple emulsions based on interfacial tension and polymer partitioning measurements.

Ref. : M. Protat, N. Bodin, F. Gobeaux, F. Malloggi, J. Daillant, N. Pantoustier, P. Guenoun and P. Perrin, Langmuir (2016), 32, 10912.

Références

Documents relatifs

Passage des Déportés 2, B-5030 Gembloux, Belgium •. Contact e-mail:

In the second set of phylogenetic analyses, we com- pared 30 ITS 2 rDNA sequences of clade C Symbiodi- nium obtained from foraminiferal hosts collected in the Gulf of Elat, Guam,

The technological advances and modeling approaches discussed in this paper provide information across a wide range of scales, and are aimed at a better characterization of the

At full activation (0 degrees of deactivation) all sizes of arches showed small median expansive forces but for individual arches the transverse force varied between expansive

For that purpose various techniques have been employed: small angle X-ray scattering allowing the determination of the influence of copolymer on the size of asphaltene

Keeping the air flow rate and thermal power of the burner constant, it is shown that even for very small flow rates of hydrogen, as low as one percent of the thermal

Le cas des joints de très faible désorientation n'a pas été aussi clairement interprété; une définition plus élaborée du nombre de sites N est nécessaitè, dàns le sens que

Even though it gives birth to higher energy pump consumption by means of high viscosity during and after phase change, special pumps can be used and the loss can