COP413L Instruction Set (Continued)
FIGURE 1. COP413C/413CH
a
"0~ ....Ao
W
o
...
o a
"0
~ ....Ao
W
o
:I: ...
o a
"0
w
....Ao
W
o
...
o a
"0
w
....AoW
o
:I:
III
::J:
o
C"),....
C")
a.. o
o
...o
C"),....
C")
a.. o
o
...::J:
o
C"),....
"'1:1'
a.. o
o
...o
C"),....
"'1:1'
a.. o o
COP413C/COP413CH Absolute Maximum Ratings
If Military! Aerospace specified devices are required, Operating Temperature Range O·Cto +70·C contact the National Semiconductor Sales Office! Storage Temperature Range - 65·C to + 150·C Distributors for availability and specifications.
Note: Absolute maximum ratings indicate limits beyond
Supply Voltage 6V which damage to the device may occur. DC and AC
electri-Voltage at Any Pin -0.3V to Vee + 0.3V cal specifications are not ensured when operating the de-Total Allowable Source Current 25mA vice at absolute maximum ratings.
Total Allowable Sink Current 25mA
DC Electrical Characteristics o·c ::;:
T A ::;: + 70·C unless otherwise specifiedCOP413C COP413CH
Parameter Conditions Units
Min Max Min Max
Operating Voltage 3.0 5.5 4.5 5.5 V
Power Supply Ripple (Note 4) 0.1 Vee 0.1 Vee V
Supply Current (Note 1) Vee = 5.0V, tc = Min 500 2000 ].LA
Vee = 3.0V, tc = Min 300 ].LA
(tc is inst. cycle)
HALT Mode Current (Note 2) Vee = 5.0V, FI = 0 kHz 30 30 ].LA
Vee = 3.0V, FI = 0 kHz 10 ].LA
Input Voltage Levels RESET, CKI
Logic High 0.9 Vee 0.9 Vee V
Logic Low 0.1 Vee 0.1 Vee V
All Other Inputs
Logic High 0.7 Vee 0.7 Vee V
Logic Low 0.2 Vee 0.2 Vee V
RESET, Sllnput Leakage -1 +1 -1 +1 ].LA
Input Capacitance 7 7 pF
Output Voltage Levels (SO, SK, L Port)
Logic High IOH = -10 p.A Vee - 0.2 Vee - 0.2 V
Logic Low IOL = 10 p.A 0.2 0.2 V
Output Current Levels
Sink (Note 3) Vee = Min, VOUT = Vee 0.2 1.2 rnA
Source (SO, SK, L Port) Vee = Min, VOUT = OV -0.1 -0.5 mA
Source (G Port) Vee = Min, VOUT = OV -8 -150 -30 -330 ].LA
Allowable Sink/Source
Current Per Pin (Note 3) 5 5 rnA
TRI-ST ATE Leakage
Current -2 +2 -2 +2 ].LA
1-84
COP413C/COP413CH
AC Electrical Characteristics
O°C ~ T A ~ 70°C unless otherwise specifiedCOP413C COP413CH
Parameter Conditions Units
Min Max Min Max
Instruction Cycle Time 16 DC 4 DC p.s
Operating CKI Frequency +8 Mode DC 500 DC 2000 kHz
Instruction Cycle Time R = 30k ±5%, Vee = 5V 8 16 p's
RC Oscillator + 4 C = 82pF ± 5%
Instruction Cycle Time R = 56k ±5%, Vee = 5V 16 32 16 32 p's
RC Oscillator + 4 (Note 6) C = 100pF ± 5%
Duty Cycle (Note 5) Fi = Max freq ext clk 40 60 40 60 %
Rise Time (Note 5) Fi = Max freq ext clk 60 60 ns
Fall Time (Note 5) Fi = Max freq ext clk 40 40 ns
Inputs (See Figure 3)
tSETUP G Inputs tc/4
+
2.8 tc/4+
0.7 p.sSllnput 1.2 0.3 P.s
L Inputs 6.8 1.7 p.s
tHOLD 1.0 0.25 P.s
Output Propagation VOUT = 1.5, CL = 100 pF
Delay RL = 5k
tpD1, tpDO 4.0 1.0 p.S
Note 1: Supply current is measured after running for 2000 cycle times with a square-wave clock on CKI. CKO open. and all other pins pulled to Vee with 5k resistors. See current drain equation on page 13.
Note 2: The Halt mode will stop CKI from oscillating.
Note 3: SO output sink current must be limited to keep VOL less tha 0.2 Vee when part is running in order to prevent entering test mode.
Note 4: Voltage change must be less than 0.5V in a 1 ms period.
Note 5: This parameter is only sampled and not 100% tested.
Note 6: Variation due to the device included.
o -a
~
...
W (') ...
(')
o
-a
~...
W (')
:J: ...
(')
o
-a w
...
w
(')...
(')
o -a w
...
w
(') :J::I:
o
C")
....
C")o
D.o ...
o
C")....
C")
o
D.o ...
:I:
o
C")
....
~o
D.o ...
o
C")....
~o
D.o
COP313C/COP313CH Absolute Maximum Ratings
If Military/Aerospace specified devices are required, Total Allowable Sink Current 25 rnA contact the National Semiconductor Sales Office/ Operating Temperature Range -40'C to + 85'C Distributors for availability and specifications.
Storage Temperature Range - 65'C to + 150'C
Supply Voltage 6V
Note: Absolute maximum ratings indicate limits beyond Voltage at Any Pin -0.3V to Vee + 0.3V which damage to the device may occur. DC and AC electri-Total Allowable Source Current 25 rnA cal specifications are not ensured when operating the
de-vice at absolute maximum ratings.
DC Electrical Characteristics
-40'C s; TA s; + 85°C unless otherwise specifiedParameter Conditions COP313C COP313CH
Units
Min Max Min Max
Operating Voltage 3.0 5.5 4.5 5.5 V
Power Supply Ripple (Note 4) 0.1 Vee 0.1 Vee V
Supply Current (Note 1) Vee = 5.0V, te = Min 600 2500
Il A
Vee = 3.0V, te = Min 360
IlA
(te is inst. cycle)
Halt Mode Current (Note 2) Vee = 5.0V, Fi = 0 kHz 50 50
IlA
Vee = 3.0V, Fi = 0 kHz 20
IlA
Input Voltage Levels RESET, CKI
Logic High 0.9 Vee 0.9 Vee V
Logic Low 0.1 Vee 0.1 Vee V
All Other Inputs
Logic High 0.7 Vee 0.7 Vee V
Logic Low 0.2 Vee 0.2 Vee V
RESET, Sllnput Leakage -2 +2 -2 +2
IlA
Input Capacitance 7 7 pF
Output Voltage Levels (SO, SK, L Port)
Logic High IOH = -10
IlA
Vee - 0.2 Vee - 0.2 VLogic Low IOL = 10
IlA
0.2 0.2 VOutput Current Levels
Sink (Note 3) Vee = Min,
Your =
Vee 0.2 1.2 rnASource (SO, SK, L Port) Vee = Min,
Your =
OV -0.1 -0.5 rnASource (G Port) Vee = Min,
Your =
OV -8 -200 -30 -440IlA
Allowable Sink/Source
Current Per Pin (Note 3) 5 5 rnA
TRI-STATE Leakage
Current3 -4 +4 -4 +4
IlA
1-86
COP313C/COP313CH
AC Electrical Characteristics
-40°C :5: TA :5:+
85°C unless otherwise specifiedParameter Conditions COP313C COP313CH
Units
Min Max Min Max
Instruction Cycle Time 16 DC 4 DC ,."s
Operating CKI Frequency -;- 8 Mode DC 500 DC 2000 kHz
Instruction Cycle Time R
=
30k ±5%, Vee=
5V 8 16 ,."sRC Oscillator -;- 4 C
=
82pF ± 5%Instruction Cycle Time R
=
56k ±5%, Vee=
5V 16 32 16 32 ,."sRC Oscillator -;- 4 (Note 6) C
=
100pF ± 5%Duty Cycle (Note 5) Fi
=
Max Freq Ext Clk 40 60 40 60 %Rise Time (Note 5) Fi
=
Max Freq Ext Clk 60 60 nsFall Time (Note 5) Fi
=
Max Freq Ext Clk 40 40 nsInputs (See Figure 3)
tSETUP G Inputs tc/4
+
2.8 tc/4+
0.7 ,."sSllnput 1.2 0.3 ,."s
L Inputs 6.8 1.7 ,."s
tHOLD 1.0 0.25 ,."s
Output Propagation VOUT
=
1.5V, CL = 100 pFDelay RL
=
5ktpD1, tpDo 4.0 1.0 ,."s
Note 1: Supply current is measured after running for 2000 cycle times with a square-wave clock on CKI. CKO open. and all other pins pulled up to Vee with 5k resistors. See current drain equation on page 13.
Note 2: The Halt mode will stop CKI from oscillating.
Note 3: SO output sink current must be limited to keep VOL less than 0.2 Vee when part is running in order to prevent entering test mode.
Note 4: Voltage change must be less than 0.5V in a 1 ms period.
Note 5: This parameter is only sampled and not 100% tested.
Note 6: Variation due to the device included.
Connection Diagram Pin Descriptions
DIP Pin Description
L7- LO 8·bit bidirectional 1/0 port with TRI·STATE
L4- 1 20 -L5
G3- GO 4·bit bidirectional 1/0 port
VCC- 2 19 -L6
SI Serial input (or counter input)
L3- 3 18 -L7
L2- 4 COP413C 17 -RESET SO Serial output (or general purpose output)
L1- 5 COP413CH 16 -CKI SK Logic·controlled clock
LO- 6 COP313C 15 -CKO (or general purpose output)
S I - 7 COP313CH 14 -G3 CKI System oscillator input
SO- 8 13 -G2
CKO Crystal oscillator output, or NC
SK- 9 12 -G1
GND- 10 11 -GO RESET System reset input
Vee System power supply
TL/DD/8537-2 GND System Ground
Top View
FIGURE 2 Order Number COP313C-XXX/D, COP313CH-XXX/D,
COP413C-XXX/D or COP413CH-XXX/D See NS Hermetic Package Number D20A Order Number COP313C-XXXIN, COP313CH-XXX/N,
COP413C-XXXIN or COP413CH-XXXIN See NS Molded Package Number N20A
o
"a~ ...10 W
o
...
o o
"a
~ ...10 W
o ::c
...o o
"a W ...10
W
o
...
o o
"a
w
...10 Wo
::c
:I:
o
C")
,....
C")
D..
o
o
...o
C"),....
C")
D..
o o
...:I:
o
C"),....
~ D..
o o
...o
C"),....
~