[PDF] Top 20 An energy based criterion for high cycle multiaxial fatigue
Has 10000 "An energy based criterion for high cycle multiaxial fatigue" found on our website. Below are the top 20 most common "An energy based criterion for high cycle multiaxial fatigue".
An energy based criterion for high cycle multiaxial fatigue
... is an open access repository that collects the work of Arts et Métiers Institute of Technology researchers and makes it freely available over the web where ...is an author-deposited version published in: ... Voir le document complet
16
A volumetric energy based high cycle multiaxial fatigue citerion
... 7KLV SDSHU SUHVHQWV DQ HYROXWLRQ RI WKH HQHUJ\ EDVHG YROXPHWULF IDWLJXH FULWHULRQ SURSRVHG E\ 3DOLQ/XF DQG /DVVHUUH >@ 7KH WKUHVKROG VWUHVV GHI QLQJ WKH YROXPH LQI XHQFLQJ IDWLJXH FUDFN [r] ... Voir le document complet
17
Estimation of the fatigue strength distribution in high-cycle multiaxial fatigue taking into account the stress–strain gradient effect
... is based on the hypothesis that no micro- damage can initiate and grow, from microscale to macroscale, without giving a certain amount of strain work in each elementary volume of material [1,19] ...In ... Voir le document complet
12
Influence of the microstructure and voids on the high-cycle fatigue strength of 316L stainless steel under multiaxial loading
... ficantly high, and given the number of realizations, loading conditions and defect sizes studied, the computations could not be achieved in a reasonable time if a crystal plasticity model is ...account for ... Voir le document complet
19
The role of the microstructure and defects on crack initiation in 316L stainless steel under multiaxial high cycle fatigue
... over an arbitrary elementary volume of these quantities give a potential explanation of the experimental scatter of the macroscopic fatigue response usually observed in ...the fatigue crack ... Voir le document complet
8
Influence of the microstructure and defects on the high cycle fatigue strength of 316L stainless steel under multiaxial loading
... the high cycle fatigue behavior of the 316L austenitic stainless steel are investigated thanks to finite element simulations of polycrystalline ...load-controlled fatigue tests are also ... Voir le document complet
3
Evaluating Schmid criterion for predicting preferential locations of persistent slip markings obtained after very high cycle fatigue for polycrystalline pure copper
... is an open access repository that collects the work of Arts et Métiers Institute of Technology researchers and makes it freely available over the web where ...is an author-deposited version published in: ... Voir le document complet
14
A continuum damage mechanics-based approach for the high cycle fatigue behavior of metallic polycrystals
... structures. For instance, such structures have been observed in copper (Lukas et ...a high dislocation density. For instance, for fatigued copper single crystals, the dislocation density ... Voir le document complet
22
Critical Plane Concept and Energy Approach in Multiaxial Fatigue
... loading cycle of an energy based para- meter can lead to results similar to an in- tegration of the resolved shear stress amplitude over each possible slip direc- tion of the critical ... Voir le document complet
10
Non-local energy based fatigue life calculation method under multiaxial variable amplitude loadings
... amplitude multiaxial fatigue loadings is still a difficult problem to handle for ...The fatigue life assessment method has to catch the full com- plexity of in service loadings (variable ... Voir le document complet
17
Multiaxial fatigue criteria based on a multiscale approach
... a criterion, the current stress is considered, in contrary to most (or all) existing fatigue ...is an important ...plane. For this reason, hydrostatic stress is preferred because it is much ... Voir le document complet
8
A mixed strain rate and energy based fatigue criterion for short fiber reinforced thermoplastics
... Second, an electro-mechanical Bose Electroforce testing machine was used in the I2M laboratory for additional ...0.1, for a total of 62 fatigue tests included in this ...Hz for most of ... Voir le document complet
14
Micro-mechanical modelling of high cycle fatigue behaviour of metals under multiaxial loads
... undertaken for different loading modes: fully reversed tensile loads, torsion and combined in-phase ...quantities for a sufficiently large number of different microstructures, a critical analysis of certain ... Voir le document complet
33
Local stress gradient approach for multiaxial fatigue behaviour assessment of high strength steels in occurrence of defects
... nowadays for making decrease the material weight of mechanical structures; hence the stress levels induced by the service loading are ...Very High Strength Steels provides by this way lightweight design and ... Voir le document complet
13
Micromechanical modeling for the probabilistic failure prediction of stents in high-cycle fatigue
... methodology for the high-cycle fatigue design of balloon-expandable ...is based on a micromechanical model coupled with a probabilistic methodology for the failure prediction of ... Voir le document complet
14
High cycle fatigue strength assessment methodology considering punching effects
... identified for (a) first specimen; (b) second ...performed. An element size of 5 μm along the X and Y directions and 10 μm along the Z direction was finally ...Because fatigue tests were conducted in ... Voir le document complet
9
Dissipation Assessments During Dynamic Very High Cycle Fatigue Tests
... are based on the thermal response of material subjected to fatigue ...loading fatigue tests involving cycle blocks with increasing stress ...the fatigue limit of the material [ 13 – 22 ... Voir le document complet
12
A crystal plasticity based approach for the modelling of high cycle fatigue damage in metallic materials
... the fatigue behaviour of metallic materials in the high cycle fatigue ...is based on a multiscale approach, which allows the connection of local deformation and damage mechanisms to ... Voir le document complet
19
High cycle thermal fatigue of austenitic stainless steel
... this energy from hot sodium (550°C) to steam generators in order to drive the turbines that eventually produce electricity ...thermal fatigue considering an equivalent strength ...mechanical ... Voir le document complet
7
Analysis of the mesoscopic high cycle multiaxial fatigue strength of fcc metals with crystal plasticity and generalized extreme values probability
... account for the microstructure variability at this length ...5-(b)). For this last FIP, the change in mesoscopic thresholds was observed especially for the biaxial loading with a phase shift of ... Voir le document complet
9
Sujets connexes