The first two digits of the 4-digit error number have the following meanings:
09XX - Hardware 10XX - Non I/O error 11 XX - Diskette error 12XX - Printer error 42XX - SDLC error
46xx - Communications information
Messages
Number Message
0999 Machine check
Execution of an invalid instruction can cause this error. This indicates either a hardware problem or a problem in the program as it is stored on your diskette.
Try to restart using a new copy of your SNA 3270 Emulation and RJE Support diskette.
1001 Invalid filename
1002 Invalid drive specification
The drive specified for the file is invalid.
Press Enter to reset the error. Respecify the drive or press Alt-Fl to cancel configuration.
1003 Invalid filename extension
1004
1005
The filename extension specified for the file is invalid. Only the .cfg extension is allowed in the configuration filename.
Press Enter to reset. Respecify the extension or press Alt -Fl to cancel.
Filename missing
A filename was not specified.
Press Enter to reset the error. Specify a filename, or press Alt -F 1 to cancel configuration.
Input exceeds field length
More characters were specified than requested. The length of the input field is indicated by the underline.
Press Enter to reset the error. Respecify the requested data, or press Alt-F 1 to cancel configuration.
1006 Invalid BAT file parameter The parameter specified in the
C3270.BAT or CSR]E.BAT file is invalid.
Press Enter to end configuration. Copy the BAT file from your SNA 3270 Emulation and RJE Support diskette.
1007 Input value is out of range
1008
1009
The input value specified was greater than or less than the allowable range.
Press Enter to reset the error. Respecify the value, or press Alt-Fl to cancel configuration.
Nonnumeric character in numeric field
A character other than 0 through 9 was specified.
Press Enter to reset the error. Specify a numeric character, or press Alt -F 1 to cancel configuration.
Invalid local address
You specified a local address that *s not within the range of hex 01 to hex FE Press Enter to reset the error. Respecify the local address, or press Alt-Fl to cancel
lUlU
1011
1012
InCOrreC[ :rue specl.lu:u
The configuration file that was specified to be modified is not a configuration file or is not the correct configuration file.
Check that the specified filename is correct. If the filename is not correct, press Enter to reset the error. Respecify the filename or press Alt -F 1 to cancel configuration.
If the filename is correct, check that you have the correct diskette in the drive. If the correct diskette is in the drive and the filename is correct, then create a new configuration file. To do this, cancel configuration (Alt-Fl), erase the existing configuration file, and then run the configuration.
Invalid character in hexadecimal field You specified a character that is not a hexadecimal value. Only hexadecimal characters are accepted in this field. Valid hexadecimal characters are 0 through 9 and A through F.
Press Enter to reset the error. Respecify the value, or press Alt-Fl to cancel configuration.
Invalid SDLC station address
You specified an SDLC station address that is not within the range of hex 01 to hex FE.
1013
1014
1015
press hnter to reset the error. Respecity the SOLC station address, or press Alt-Fl to cancel configuration.
Required value not given You did not specify an answer to a required question. The question
appearing on your screen is not optional.
You must specify an answer.
Press Enter to reset the error. Specify an answer, or press Alt -F 1 to cancel
configuration.
Invalid key assignment
You specified a key assignment value that is not within the range of 00 to 44.
Press Enter to reset the error. Respecify the key assignment value, or press Alt-Fl to cancel configuration.
Unexpected error nn
An unexpected error occurred. The error was detected by BASIC. The error number nn is the BASIC error code. For additional information, see Appendix A, "Messages"
in the IBM Personal Computer BASIC book.
Press Enter to continue. Configuration will be canceled. You will be returned to
IU:lI
1022
1023
Punch stream trom nost ana output device is not assigned
No device is assigned for the punch streanl just received.
Press End to reset the error. The host will be notified that the stream was not accepted. Use the MODIFY command to assign a punch stream device (PU 1 = D).
Send a console command to the host that requests the punch stream to be sent again.
Excha stream from host and output device is not assigned
No device is assigned for the exchange stream just received.
Press End to reset the error. The host will be notified that the stream was not accepted. Use the MODIFY command to assign an exchange stream device
(EXC = D). Send a console command to the host that requests the exchange stream be sent again.
Print stream from host and output device is not assigned
No device is assigned for the print stream just received.
Press End to reset the error. The host will be notified that the stream was not accepted. Use the MODIFY command to
llUU
1101
Juespec d.Irectory tull, d.iskette not initialized, or invalid drive
The file cannot be opened because either:
• The diskette that you specified already contains the maximum number of files.
• The diskette that you specified has not been formatted.
• Your IBM Personal Computer does not have the diskette drive that you specified.
You correct the problem by either:
• Inserting the correct diskette and pressing End to reset the error.
• Pressing End to reset the error and specifying the correct drive with a MODIFY command statement.
For host streams, the host will be notified that the IBM Personal Computer could not accept the stream. Ask the host to send it again.
filespec not found or invalid drive The file was not found on the diskette in the drive you specified or you specified a drive that does not exist.
1102
1103
1104
filespec not found on a close When a close was attempted, the file being written to or read from was no longer in the drive specified.
Insert the original diskette so that RJE can close the file and update the directory.
Press End to reset the error. If you cannot find the original diskette, press Ctrl-Break toendRJE.
filespec drive not ready
The door was open on the drive you specified.
Close the door. Press End to reset the error. Retry the operation.
Note: The indicated drive may show Ix: for the DOS default drive, Iz: for the invalid drive specified, or the indicated drive may be incorrect, that is, show la: when the drive not ready is Ib: The latter case may occur when multiple drives have open files and one drive is not ready.
filespec attempt to write on write protected diskette
The file was opened but the write failed because the diskette is write protected.
Remove this diskette and insert the correct diskette. If this is the correct diskette, remove the write protect tab.
1105
1106
filespec syslog wrapping
The syslog file is full and has been closed.
RJE allocates a syslog file to contain 200 records. If the diskette contains
insufficient free space, RJE allocates syslog the maximum size available.
If you want to save this syslog file, put a new diskette in the drive. Press End to reset the error.
If you want to reuse this file (allow syslog to wrap), press End to reset the error.
filespec diskette is full
The diskette receiving a print, punch, or exchange file is full and the file has been closed.
Press End to reset. The host will be notified that the stream has been terminated. You will probably want to rerun this job, starting with a blank formatted diskette that can contain the entire stream.
If you choose not to rerun your job, then you may be able to restart the data stream with a host command. Another file will be opened. You will have to determine the contents of each file and, if necessary, merge them. Some of the data may be repeated on the new file.
1111-1115
1125
1126
filespec errors
1111 filespec data error 1112 filespec seek error 1113 filespec sector not found 1114 filespec write fault 1115 filespec general diskette
failure
A serious DOS error has occurred. The diskette operation cannot continue.
Press End to reset the error.
Configuration file error nn
A file error occurred while reading or writing the configuration file. The error was detected by BASIC. The error number nn is the BASIC error. For additional information, see the explanation of this error in the IBM Personal Computer BAS/Cbook.
Press Enter to reset the error.
Configuration will be canceled. You will be returned to DOS.
Drive not ready
The configuration diskette drive door is open or the diskette is not in the drive.
1127
1128
1129
Put the configuration diskette in the drive.
Press Enter to reset the error.
Diskette write protected You tried to create or modify a configuration file. The configuration diskette is write protected.
Insert an unprotected diskette and press Enter to reset, or press Alt -F 1 to cancel.
If the correct diskette is already in the specified drive, remove the write-protect tab, and press Enter to reset.
Directory space unavailable
You tried to create a new configuration file. The diskette directory is full.
Insert a new diskette. Press Enter to reset the error, or press Alt -F 1 to cancel configuration.
File space unavailable
You tried to create a new configuration file . No file space is available on the diskette.
Insert a new diskette. Press Enter to reset the error, or press Alt -F 1 to cancel configuration.
1210
Prtnter power OIl or not anacnea Either your printer is powered off or it is not attached.
This error occurs if your printer is powered off or not attached when you start RJE. If you want to run RJE with a printer, attach the printer and switch the power on. Press End to reset the error.
If you choose not to run RJE with a printer, press End to reset the error.
This error also occurs if you power off the printer while printing. If you power off the printer while receiving a print stream, the print stream device is set to not assigned and the host is notified that you are unable to continue to accept the print stream at this time. Press Enter to reset the error.
If you power off the printer while printing the log, you can power on the printer and press End to reset the error.
Printer error
During RJE operation, this error occurs because of a serious printer error. If this error occurs while a print stream is being sent to the printer, the print stream device is set to not assigned and the host is notified that the IBM Personal Computer is unable to accept the print stream at this time.