• Aucun résultat trouvé

Finite volume modeling of laser assisted frictionstir welding of 2017A-T451 aluminum alloy forenhanced sustainability of welded joints.

N/A
N/A
Info
Télécharger
Protected

Academic year: 2021

Partager "Finite volume modeling of laser assisted frictionstir welding of 2017A-T451 aluminum alloy forenhanced sustainability of welded joints."

Copied!
1
0
0

Chargement.... (Voir le texte intégral maintenant)

Texte intégral

(1)

AIP Conference. Proceding

Volume 1769, Issue 100014, 2016, Pages 1-5

Finite volume modeling of laser assisted friction stir welding of 2017A-T451 aluminum alloy for

enhanced sustainability of welded joints.

Oussama Mimouni, Riad BADJI, Mohamed HADJI, Afia Kouadri- Henni

Abstract: This study focuses on a new welding modification friction stir welding, using a preheating during the welding phase. This method utilizes laser energy to pre-heat the workpiece to a localized area at the front of the FSW tool, thereby reducing the temperature gradient over a localized area in advance of the tool. The amount of heat generated during welding determines the quality of the weld. Therefore the understanding of the temperature distribution is required to determine the optimal method of welding parameters. In this study, a two-dimensional model of an aluminum alloy plate coupled to a circular laser source is developed, using FLUENT software that is based on the finite volume method, also the geometry of the pin of the FSW tool was modified in several configurations to highlight the effect of the geometry of the tool on the temperature distribution in the welded plate. The model developed can be used to better understand the process, predict process performance and to determine the optimal parameters of the process.

Keywords : riction stir welding, 2017A-T451 aluminum alloy, Finite volume modeling

Centre de Recherche en Technologies Industrielles - CRTI - www.crti.dz

Powered by TCPDF (www.tcpdf.org)

Références

Télécharger maintenant ( PDF - 1 Page - 7.75 KB )

Documents relatifs

Semi-analytical study on the generic degeneracy for galaxy clustering measurements

Observations of the growth rate f from large scale structures using Redshift Space Distortions (RSD), give a direct way to test different dark energy models, Song & Percival

Torymus sinensis: a viable management option for the biological control of Dryocosmus kuriphilus in Europe?

sinensis is the only biological control agent shown to have hybridized with a native species, it is very likely that the proposed stepwise environmental risk assessment scheme

A key region in the human parietal cortex for processing proprioceptive hand feedback during reaching movements

The trajectories are rotated into the plane of the reaching direction and plotted relative to the force perturbation (the force perturbation is directed to the positive

Laser welding of dissimilar copper and aluminum sheets by shaping the laser pulses

In this study, the power modulation as a function of time for seam welding of thin sheets of Cu-Al (Copper on top) in overlap configuration is studied.. This configuration favors

Laser polishing of Aluminum and Polyamide for dissimilar laser welded assemblies

A brief comparison between EDS analysis of the samples before and after the LP process (figures 4-b and 5-b), shows a substantial increase of oxygen content after the LP

A STUDY OF THE INFLUENCE OF THE WIDTH OF CUT ON MICRO MILLING ALUMINUM ALLOY

It is presented an experimental study on micro milling aluminum alloy with different width of cut in order to identity the influence of the minimum chip thickness on the

Construction des stratégies et des performances dans les circuits courts alimentaires : entre encastrement relationnel et gestionnaire

Pour compléter la prise en compte de l’encastrement relationnel, nous proposons d’adopter cette double perspective, encastrement gestionnaire et possibilité de contre-performation,

Chip morphology and delamination characterization for vibration-assisted drilling of carbon fiber-reinforced polymer

In contrast, at a lower thermal load (N = 2000 rpm), increasing the LF-VAD amplitude resulted in a higher impact velocity and larger uncut chip thickness (see Section 3).. Effect