ADAPTEC ACB-4525S4000
• supports narrow SCSI bus
• supports up to two 10MHz ESDI hard drives, hard sectored with up to 36 sectors per track
• supports automatic drive media defect management
J0
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ :::::::::::::::::::::::::1 Ü ³
³ SCSI LED ³
³ ±± ±± ³
³ ±± ±± ³
³ ±± ±± ³
³ ±± ±± ³
³ Terminator Terminator ³
³ ³
³ ³
³ ³
³ ³
³ J5 ³
³ ÚÄÄ¿ ³
³ P³ùù³O ³
³ N³ùù³M ³
³ L³ùù³K ³
³ J³ùù³I ³
³ H³ùù³G ³
³ F³ùù³E ³
³ D³ùù³C ³
³ B³ùù³A ³
³ ÀÄÄÙ ³
³ ESDI ³
³ ESDI Data Cable ³
³±±Power±±±ÚÄ¿ËËControl CableËËÚÄ¿ HD2 HD1 ³
³±±±±±±±±±±³ ³ººººººººººººººººº³ ³ :::::::::: :::::::::: ³ ÀÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ J1 J2 J4 J3
SCSI Bus Termination
Leave both terminators in place if the SCSI host adapter is connected to one end of the SCSI cable and the ACB-4525S4000 to the other end.
Pull both terminators if the ACB-4525S4000 is connected between the SCSI host adapter and another SCSI device.
ACB-4525S4000 (http://www.franken-online.de/ymmv) Page 1 of 2
J5 Jumper Options
³ IN ³ OUT ³ default ÚÄÄ¿ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄ P³ùù³O Diagnostic Mode ³enabled ³disabled ³disabled N³ùù³M SCSI Parity Check ³enabled ³disabled ³enabled L³ùù³K SCSI Unit Attention ³disabled ³enabled ³enabled J³ùù³I Start Drive Motor ³by SCSI command ³at Power Up ³at Power Up H³ùù³G ACB-5500/4000 compatibility ³enabled ³disabled ³disabled F³ùù³E SCSI Address
D³ùù³C SCSI Address B³ùù³A SCSI Address ÀÄÄÙ
SCSI Address
Address ³ BA ³ DC ³ FE ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄ 0 ³ OUT ³ OUT ³ OUT 1 ³ IN ³ OUT ³ OUT 2 ³ OUT ³ IN ³ OUT 3 ³ IN ³ IN ³ OUT 4 ³ OUT ³ OUT ³ IN 5 ³ IN ³ OUT ³ IN 6 ³ OUT ³ IN ³ IN 7 ³ IN ³ IN ³ IN
Board Connectors
J0 50-pin SCSI connector J1 4-pin power connector
J2 34-pin control cable connector hard drive J3 20-pin data cable connector drive 1
J4 20-pin data cable connector drive 2
Setup
The SCSI host adapter hard disk format program initializes the ESDI hard drive with a low-level format.
In case of Adaptec SCSI host adapters, this process is done within the DOS operating system. At the DOS start up, a host adapter specific ASPI driver has to be loaded with the help of a config.sys entry. Then 'scsifmt.exe' from Adaptec initializes the drive.
ACB-4525S4000 http://www.franken-online.de/ymmv) Page 2 of 2