• Aucun résultat trouvé

Propriétés électriques de cellule solaire à base dediSéléniure de Cuivre Indium Galium CuIn(1?x)GaxSe2 (CIGS)

N/A
N/A
Protected

Academic year: 2021

Partager "Propriétés électriques de cellule solaire à base dediSéléniure de Cuivre Indium Galium CuIn(1?x)GaxSe2 (CIGS)"

Copied!
1
0
0

Texte intégral

(1)

Hichem AMAR, 2014, «Propriétés électriques de cellule solaire à base dediSéléniure de Cuivre Indium Galium CuIn(1?x)GaxSe2 (CIGS)», Mémoire de magister, Université Mohamed Khider de Biskra

Propriétés électriques de cellule solaire à base dediSéléniure de Cuivre Indium Galium

CuIn(1?x)GaxSe2 (CIGS)

Hichem AMAR

Soutenue en: 2014

Abstract : The work of this memory of Magister is a numerical simulation study of electricalcharacteristics of a solar cell and thin-film heterojunction ZnO / CdS (n) / CIGS (p) / Mousing Silvaco software Atlas-2D. The electrical characteristics of current density versusvoltage J (V) under AM1.5 illumination are simulated: the conversion efficiency ?= 20.1%,the open-circuit voltage Voc = 0.68 V, the current density of short Circuit Jcc = 36.91 mA /cm ² and the form factor FF = 80%. These simulation results are in very good agreement withthose found experimentally. The photovoltaic parameters of the solar cell are studied andanalyzed by the variation of parameters: thickness and doping of CdS and CIGS layers, thecomposition of Galium compared to indium x. It was found that the variation of theparameters of the front-layer (CdS) has generally less significant effects on the electricalcharacteristics of the cell in comparison with the parameters of the absorption layer (CIGS).The simulation results showed that the molar fraction x of the CIGS layer has an optimalvalue around 0.31 corresponding to an energy gap of 1.16 eV, this result is in good agreementwith that found experimentally. A small improvement in the performance of CIGS solar cellwas made by the addition of the window layer ZnO: Al.

Keywords : Keywords: Numerical simulation -Silvaco- Atlas-2D – CIGS solar cell –solar cell parameters.

Centre de Recherche en Technologies Industrielles - CRTI - www.crti.dz

Powered by TCPDF (www.tcpdf.org)

Références

Documents relatifs

The obtained results show that the TCO work function should be large enough to achieve high conversion efficiency for superstrate CIGS solar cell. Nevertheless, it is desirable

Abstract : Résumé Dans ce travail nous avons effectué l’étude des caractéristiques électriques, une analyse numérique à deux dimensions en utilisant la technologie

Dans cette étude, nous allons simuler l'effet de l'épaisseur et le dopage des couches en CIGS et la fraction molaire x sur les paramètres photovoltaïques de la

The simulation results also showed that the rise of the CdS thickness decreases all output parameters and the external quantum efficiency while the rise of the CIGS thickness

The messages that can be send to the Conductivity circuit and how they are translated for the serial communi- cation between the BeagleBone Black and the OpenROV Controller board can

Nevertheless none of these contributions investigates and compares the basic properties of printed transmission lines (effective permittivity, characteristic

As described above, the optimization task we have now to undertake is the optimization of the cell e fficiency η, which is a function of four parameters, the InGaN layer thickness,

The work of this memory of Magister is a numerical simulation study of electrical characteristics of a solar cell and thin-film heterojunction ZnO / CdS (n) / CIGS (p) / Mo