Haut PDF Quantitative relationships between chemical composition, microstructure and mechanical properties for bainitic steels
Quantitative relationships between chemical composition, microstructure and mechanical properties for bainitic steels
... site for cleavage leads to final fracture. This site was found between 600µm and 1300µm (950µm in average) beyond the notch ...76. For most specimens the initiation site is a single coarse ...
262
Microstructure-mechanical properties relationships in vibration welded glass-fiber-reinforced polyamide 66: A high-resolution X-ray microtomography study
... orientation and pressure). In order to assess re- lationships between microstructure and mechanical properties more quantitatively, we first investigate the impact of the welding ...
13
Supramolecular assembly of gelatin and inorganic polyanions: Fine-tuning the mechanical properties of nanocomposites by varying their composition and microstructure
... soft chemical approach that implies the assembly of inorganic polyanions and gelatin in aqueous ...the chemical procedure by which the components are brought together (pH, concentration, molar ...
14
Supramolecular assembly of gelatin and inorganic polyanions: Fine-tuning the mechanical properties of nanocomposites by varying their composition and microstructure
... soft chemical approach that implies the assembly of inorganic polyanions and gelatin in aqueous ...the chemical procedure by which the components are brought together (pH, concentration, molar ...
14
Investigation of the relationship between mechanical properties and microstructure in a Fe-9%Cr ODS steel
... formula and the chemical composition of the material, one finds a carbon loss of approximatively 70% due to the austenitisation during 20 minutes at ...higher mechanical properties ...
8
Relation between microstructure induced by oxidation and room-temperature mechanical properties of the thermally grown oxide scales on austenitic stainless steels
... testing for two austenitic stainless steels with close composition except their S ...correlation between damage patterns, microstructure, mechanical and adhesion ...
11
Relationship between microstructure and mechanical properties of a 5% Cr tempered martensitic tool steel
... Introduction Steels containing 5% Cr (AISI H11) were particularly de- veloped for high temperature metal forming operations as pressure die casting for light alloys injection, forging dies, .... ...
6
Relation between microstructure induced by oxidation and room-temperature mechanical properties of the thermally grown oxide scales on austenitic stainless steels
... testing for two austenitic stainless steels with close composition except their S ...correlation between damage patterns, microstructure, mechanical and adhesion ...
12
Correlation between quenching rate, mechanical properties and microstructure in thick sections of Al Mg Si( Cu) alloys
... the chemical composition speci ed in Table ...forging and was thermally treated at 530°C for 4h then tempered at 175°C for ... uid for each cube (air, oil, water) and an ...
14
The Relationship between microstructure and mechanical properties of strand Steel wires
... continuation and an extension of our previous works in ...9.00 and 13.00 mm containing approximately 0.88 wt. % of carbon intended for manufacture of ...wiredrawing and manufacture of welding ...
3
Grain and phase stress criteria for behaviour and cleavage in duplex and bainitic steels
... damage; microstructure; phase interac- tions; stress ...of steels involves the use of var- ious techniques (such as rolling, casting, welding, machin- ing, ...ical properties of ...its ...
14
Microstructure-mechanical properties relationships in vibration welded glass-fiber-reinforced polyamide 66: A high-resolution X-ray microtomography study
... orientation and pressure). In order to assess re- lationships between microstructure and mechanical properties more quantitatively, we first investigate the impact of the welding ...
13
Microstructure and mechanical properties of continuous equal channel angular pressed Titanium
... EBSD and TEM observations. The change of the fraction of low and high-angle boundaries in Ti during ECAP-Conform has been analyzed ...temperature and deformation conditions the microstructure ...
8
Relationships between anatomical and vibrational properties of wavy sycamore maple
... makers for back plates of string instruments such as violins and guitars (Bucur ...speaking, properties that are important for instrument plates are density (ρ), Young’s modulus (E’), specific ...
30
Carbon nanotube–metal–oxide nanocomposites: microstructure, electrical conductivity and mechanical properties
... reported, for MWNTs–poly- mer composites, an electrical conductivity equal to 10 ⫺2 S cm ⫺1 with only ...[3] and Yoshino et al. measured 0.05–0.30 S cm ⫺1 with 10 and 20 vol% of MWNTs, respectively ...
11
Carbon nanotube-metal-oxide nanocomposites: microstructure, electrical conductivity and mechanical properties
... the mechanical reinforce- ment [34]. In contrast, for CMA2 and for the com- posite in ...CMA1 and in the dense CMA2 speci- men, the pores are smaller, less elongated but more numerous ...
12
Effect of Microstructural and Physical Mechanisms on Mechanical Properties of Single-Phase Steels
... except for the initial critical resolved shear stress τ c 0 , the immobilization parameter I and the recovery parameter ...(5) for the evolution of the randomly distributed ...storage and ...
6
Relations between oxidation induced microstructure and mechanical durability of oxide scales
... production and composition are described in [ 8 , 9 ...machining and ground with SiC paper down to a final grade of ...thick and a gauge length of 3 mm [ 8 ...
13
Mechanical Properties and Microstructure of AZ31B Magnesium Alloy Processed by I-ECAP
... size and its orientation in twin formation are ...B and C compressed to true strain of ...area, and the results are shown in Table I ...observed for the sample A and not in the cases of ...
13
Effect of Heat Treatment and Chemical Composition on the Mechanical Properties of a 357 Semi-solid Alloy using SEED
... This publication could be one of several versions: author’s original, accepted manuscript or the publisher’s version. / La version de cette publication peut être l’une des suivantes : la version prépublication de ...
9