[PDF] Top 20 Oxidation Assisted Intergranular Cracking in Alloy 718: Effects of Strain Rate and Temperature
Has 10000 "Oxidation Assisted Intergranular Cracking in Alloy 718: Effects of Strain Rate and Temperature" found on our website. Below are the top 20 most common "Oxidation Assisted Intergranular Cracking in Alloy 718: Effects of Strain Rate and Temperature".
Oxidation Assisted Intergranular Cracking in Alloy 718: Effects of Strain Rate and Temperature
... microstructure of the alloy, oxidation assisted inter- granular cracking in alloy 718 is still an open and important ...Results and observations ... Voir le document complet
8
A Re-examination of the Portevin-Le Chatelier Effect in Alloy 718 in Connection with Oxidation-Assisted Intergranular Cracking
... EXPERIMENTAL Alloy 718 used in the present study was provided in the form of single coil of rolled thin strip ...thick) in the solutionized state. The alloy ... Voir le document complet
13
Influence of local mechanical loadings paths on the oxidation assisted crack initiation of alloy 718
... showing strain–strain rate paths fol- lowed by the material located in the apex of the V can easily be ...the strain rate interval demarcating the disappearance/appearance ... Voir le document complet
8
Influence of local mechanical loadings paths on the oxidation assisted crack initiation of alloy 718
... showing strain–strain rate paths fol- lowed by the material located in the apex of the V can easily be ...the strain rate interval demarcating the disappearance/appearance ... Voir le document complet
9
Strain rate and oxidation effects on crack initiation at 600 and 650 °C in a nickel-based superalloy
... aged alloy 718, Oxidation, Environment assisted cracking Introduction Alloy 718 is a nickel-based superalloy used for a wide range RI DSSOLFDWLRQV LQ ¿HOGV LQFOXGLQJ ... Voir le document complet
8
Influence of interstitials content on the sensitivity of alloy 718 to oxidation assisted intergranular fracture
... rates in the temperature range ...mode of each sample are plotted on a strain rate-temperature diagram ...Fig.4 and Fig. 5). On the same plot, the occurrence of PLC ... Voir le document complet
10
Strain rate and oxidation effects on crack initiation at 600 and 650 °C in a nickel-based superalloy
... aged alloy 718, Oxidation, Environment assisted cracking Introduction Alloy 718 is a nickel-based superalloy used for a wide range RI DSSOLFDWLRQV LQ ¿HOGV LQFOXGLQJ ... Voir le document complet
9
A Re-examination of the Portevin-Le Chatelier Effect in Alloy 718 in Connection with Oxidation-Assisted Intergranular Cracking
... effect of oxidation on the mechanical behavior of alloy 718 for temperatures ranging from 673 K to 873 K (400 C to 600 C) and at a strain rate of 5 9 10 7 ... Voir le document complet
12
Influence of δ phase precipitation on the stress corrosion cracking resistance of alloy 718 in PWR primary water
... influence of d phase on the intergranular stress corrosion cracking (IGSCC) resistance of alloy 718 is commonly taken for ...granted. In addition, d phase formed at low ... Voir le document complet
7
Intergranular Corrosion of 2024 Alloy in Chloride Solutions
... particles in the material. Intergranular immersion ...kinetics of inter- granular corrosion in 2024 ...sectioned and observed by means of an optical ...2024 alloy after ... Voir le document complet
10
Intergranular Corrosion of 2024 Alloy in Chloride Solutions
... particles in the material. Intergranular immersion ...kinetics of inter- granular corrosion in 2024 ...sectioned and observed by means of an optical ...2024 alloy after ... Voir le document complet
9
High temperature oxidation of IN 718 manufactured by laser beam melting and electron beam melting: Effect of surface topography
... topography of the samples was characterized using an interferometric and confocal variation ...diameter of the particles used for EBM samples ranged from 45 to 105 μm with a 75-μm layer-thickness, ... Voir le document complet
20
The strain rate and temperature dependence of Young's modulus of ice
... READ THESE TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS WEBSITE. https://nrc-publications.canada.ca/eng/copyright Vous avez des questions? Nous pouvons vous aider. Pour communiquer directement avec un auteur, ... Voir le document complet
12
Low Temperature Strain Rate Sensitivity of Titanium Alloys
... Results and discussion The evolution of the tensile properties for the two alloys, the ...plastic strain flow stress σ 0.2 , the ultimate tensile stress σ m and the plastic strain up to ... Voir le document complet
6
Low Temperature Strain Rate Sensitivity of Titanium Alloys
... microstructure of (a) Ti-6Al-4V and (b) Ti-β21S ...furnace and a 100kN load cell was used for tensile testing at the imposed displacement ...kinds of specimens were used for the tensile tests: ... Voir le document complet
5
Constitutive model incorporating the strain-rate and state of stress effects for machining simulation of titanium alloy Ti6Al4V
... is of particular importance because metal cutting is the physical separation of the layer being removed (in the form of chips) from the rest of the ...process of physical ... Voir le document complet
5
Effect of temperature on hydrogen embrittlement susceptibility of alloy 718 in Light Water Reactor environment
... influence of y' and y• pre cipitates, further mechanical tests were conducted at 300 •c, but with a higher strain rate ...promote strain localization around y' and y• pre ... Voir le document complet
9
Effect of temperature on hydrogen embrittlement susceptibility of alloy 718 in Light Water Reactor environment
... complexes and dislocations by using multi scale simulation techniques ...role of hydrogen vacancy complexes on nano voids formation due to dislocation plasticity in a Fe during ...concentration ... Voir le document complet
10
Strain rate effects on localized necking in substrate-supported metal layers
... necking in metal/elastomer bilayers by increasing the elastomer relative ...point of view, this conclusion is very important for the design of parts and components made of ... Voir le document complet
22
Fibre orientation effects on high strain rate of carbon / epoxy composites
... included in a laminate, the material law that is used in the computations must be a linear law corresponding to the laminate ...law. In order to estimate the precracking influence on material’s ... Voir le document complet
16
Sujets connexes