steel and stainless steel properties
Microstructure and mechanical properties relationship of additively manufactured 316L stainless steel by selective laser melting
... Materials and Processes, CEA, Université Paris-Saclay, 91191 Gif-sur-Yvette, France Received: 24 January 2019 / Received in final form: 24 September 2019 / Accepted: 23 October 2019 ...fast and complex ...
11
Mechanical properties and tribological behavior of a silica or/and alumina coating prepared by sol-gel route on stainless steel
... Adhesive properties of films were evaluated by a Nano-Scratch tester (NST, CSM Instruments) to measure critical loads of crack formation or ...−1 and a maximum normal load of 100 ...316-L stainless ...
8
Hybrid laser-arc welding of cast martensitic stainless steel ca6nm: post-weld tempered microstructure and mechanical properties
... martensitic stainless steel, was carried out in butt joint configuration using a continuous wave fiber laser at its maximum power of ...zone and base metal were characterized after post- weld ...
17
Mechanical properties and tribological behavior of a silica or/and alumina coating prepared by sol-gel route on stainless steel
... Adhesive properties of films were evaluated by a Nano-Scratch tester (NST, CSM Instruments) to measure critical loads of crack formation or ...−1 and a maximum normal load of 100 ...316-L stainless ...
9
Structure and Properties of Open-Cell 316L Stainless Steel Foams Produced by a Powder Metallurgy-Based Process
... Access and use of this website and the material on it are subject to the Terms and Conditions set forth at Structure and Properties of Open-Cell 316L Stainless Steel Foams ...
2
Corrosion properties of 17-4 PH martensitic stainless steel obtained by additive manufacturing
... ng and heating rates experienced during fabrication the obtained materials present different microstructures from their wrought ...PH stainless steel obtained by SLM was investigated in acidic ...
153
Preparation and characterization of electrolytic alumina deposit on austenitic stainless steel
... austenitic stainless steel was dipped in sulphuric acid solution at 20% (purity 98%) for 10 s and then was dipped in acid solution containing additives such as thiosulphate and propargyl ...
7
A robust antibacterial coating for stainless steel
... mechanical and esthetical properties, stainless steel is widely used in the daily life, not only in the building industry but also in the food industry, the appliances or in the medical field, ...
2
The effect of annealing on the mechanical properties of iron: stainless steel composistes
... L’accès à ce site Web et l’utilisation de son contenu sont assujettis aux conditions présentées dans le site LISEZ CES CONDITIONS ATTENTIVEMENT AVANT D’UTILISER CE SITE WEB. [Proceedings of the Conference], 2016-05 READ ...
6
Cold drawing of austenitic stainless steel wire
... These theories all relete the draw stress to die helf-sngle, coefficient of friction, reduction in area, and mechanical properties of the material. A simpler tool for analysis of the wire drawing process is ...
34
Electrochemical activity of Geobacter sulfurreducens biofilms on stainless steel anodes
... framework, stainless steel was checked here because of its large industrial availability, mechanical properties, long-term resistance to corrosion and reasonable ...the stainless ...
14
2018 — Machinability of stainless steel alloys
... power and strength wanted to do the ...forces and the chip formation during certain machining ...life and edge safety is a very important factor in the design of the cutting ...(hc), and the ...
125
Stainless steel beam-columns in case of fire
... carbon steel S 235 and stainless steel ...accuracy and safety of the Eurocode 3 design formulae for the evaluation of the fire resistance of ...on stainless steel ...
8
Duplex stainless steel columns and beam-columns in case of fire
... The stainless steels can be subdivided in five basic groups, according to their metallurgical structure: the austenitic, ferritic, martensitic, duplex austenitic-ferritic and precipitation-hardening groups ...
11
Effect of hardening heat treatment on the mechanical properties of a 17-4PH stainless steel foam
... books and journal reviews ...metals and alloys might be better suited for applications where aluminium is not adequate from the mechanical, chemical and/or thermal point of ...respect, ...
15
Low-temperature plasma nitriding of martensitic stainless steel
... mechanical properties. However, the wear and corrosion resistance of these steels need to improve for the wide- spread ...these properties to prolong the life of tools. Hard and corrosion ...
6
Laser Ignition of Bulk Iron, Mild Steel, and Stainless Steel in Oxygen Atmospheres
... mild steel S355J, and stainless steel 316L has been ...ignition and combustion processes have been monitored using a high-speed video camera and adapted ...iron and mild ...
23
Microbial electrocatalysis with Geobacter sulfurreducens biofilm on stainless steel cathodes
... bioremediation. Stainless steel was tested here following a pro- cedure already described in the literature, based on the catalysis of fumarate reduction by biofilms formed in pure culture of ...reached, ...
7
Investigations on drilling performance of high resistant austenitic stainless steel
... 1. Introduction Nowadays HRASS is an attractive engineering material in engine automotive applications due to its outstanding innate properties among which a high mechanical resistance at high temperature even in ...
12
Catalytic coatings on stainless steel prepared by sol–gel route
... on stainless steel substrates. The homogeneity and the quality of the film were optimal when the sol was ...area and a good thermal ...
13