Interfacial toughness
Apparent Interfacial Toughness of Undoped and Photoluminescent Eu3+-Doped Yttria-Stabilized Zirconia Thermal Barrier Coatings
... the interfacial toughness results, there is statistically no difference between Eu-doped coatings and undoped coatings regarding microstructural characteristics and mechanical ...the toughness of the ...
12
Apparent Interfacial Toughness of Undoped and Photoluminescent Eu3+-Doped Yttria-Stabilized Zirconia Thermal Barrier Coatings
... the interfacial toughness, which is an important factor to address thermal barrier coating’s per- formance and ...the interfacial toughness of TBC deposited by atmospheric plasma spray is ...
12
Influence of isothermal and cyclic oxidation on the apparent interfacial toughness in thermal barrier coating systems
... fracture toughness measurement for various substrate/coating systems, including “four point bending test” [3] , “barb test” [4] , “buckling test” [5] , “micro-bending test” [6] and various inden- tation techniques ...
8
Influence of isothermal and cyclic oxidation on the apparent interfacial toughness in thermal barrier coating systems
... fracture toughness measurement for various substrate/coating systems, including “four point bending test” [3] , “barb test” [4] , “buckling test” [5] , “micro-bending test” [6] and various inden- tation techniques ...
9
Interfacial toughness of the nickel-nickel oxide system
... fracture toughness of the oxide as well as the frac- ture toughness of the interface versus the oxide thick- ness is plotted in ...fracture toughness of the oxide varies very little with the TGO ...
5
Influence of isothermal aging conditions on APS TBC's interfacial fracture toughness
... apparent toughness K ca and oxide thickness ζ are given in Table 7 ...measurable interfacial crack, as well as the interfacial toughness, de- crease with the severity of the high temperature ...
9
Measurement of fracture toughness of metallic materials produced by additive manufacturing
... fracture toughness of AM Ti-6Al- 4V [12, 17-19, 23, 25], although this is a key point in the damage tolerance ...Ti-6Al-4V toughness obtained with Laser Beam Melting (LBM) and Electron Beam Melting (EBM) ...
26
Local approach applied to the fracture toughness of resistance spot welds
... 4.4. Assessment of a cleavage crack initiation criterion using the UXT test The stress state in the nugget during the UXT test is described here by considering Steel D tested at room temperature (Fig. 8a-b). The central ...
11
Nonequilibrium Interfacial Tension in Simple and Complex Fluids
... DOI: 10.1103/PhysRevX.6.041057 Subject Areas: Fluid Dynamics, Soft Matter I. INTRODUCTION The spherical shape of soap bubbles and liquid droplets, the capillary forces responsible, e.g., for the sap rise in trees, the ...
13
Test methods for measuring pure mode III delamination toughness of composite
... Two testing methods for mode III experiments were evaluated: a novel test proposed in our previous study, termed Edge Ring Crack Torsion (ERCT) test, and the widely used Edge Crack Torsi[r] ...
9
Interfacial rheological properties of self-assembling biopolymer microcapsules
... in interfacial rheological properties of capsule mem- ...step interfacial complexation of polyelectrolytes allows to gener- ate various uniform suspensions of ...the interfacial rheological ...
11
Couplage interfacial de modèles en dynamique des fluides. Application aux écoulements diphasiques.
... leur propre modélisation se rejoignent à des intersections. La simulation numérique des échanges entre océan et atmosphère dans [77] est un autre exemple de couplage interfacial. Dans le cas d’un problème de la ...
293
Interfacial Control of Magnetic Properties at LaMnO3/LaNiO3 Interfaces
... Therefore, there is an intrinsic structural asymmetry between the two LMO −LNO interfaces with a concomitant asymmetry in charge transfer, with both phenomena present throughout the entire superlattice and independent ...
8
Multi-scale approach of the instrumented indentation technique on the fracture toughness estimation
... toughness of 7050 aluminum alloy with the Berkovich indenter” Materials and Design 40, pp. 176-‐184. [4] L. Kachanov (1958), Ivz Akad Nauk USSR Otd Tech, pp. 8-‐26. [5] F.M. Xue, F.G. Li, J. Li, M. He (2012) ...
3
Calculation of the long range interactions for interfacial properties
... For Peer Review Only 1 INTRODUCTION Most of the phenomena in surface science (adhesion, wetting, and lubrication) involve the combination of liquid-liquid, liquid-vapour, and liquid-solid interfaces. Many important ...
28
Interfacial analysis of n-ALKANETHIOL SAMs on GaAs(001) by ARXPS
... Archives des publications du CNRC For the publisher’s version, please access the DOI link below./ Pour consulter la version de l’éditeur, utilisez le lien DOI ci-dessous. Access and use of this website and the material ...
16
Effect of interfacial crystalline growth on autohesion of PEEK
... A B S T R A C T This work aims to clarify the role of the crystalline growth on the autohesion strength of amorphous PEEK below its melting temperature. The self-bonding strength versus temperature, pressure and time has ...
8
RPV fracture toughness of various metallurgical zones at very high fluences
... fracture toughness data are analyzed with Master Curve methodology and compared to the ETC pre- diction. The last section is dedicated to fractographic investigations. Materials and Irradiation conditions The two ...
13
Influence of the degree of mineralization of the cortical bone on toughness
... Figure 2. grey level images of two thick sections of cortical bone used for dmB analysis. (a) female 91 y.o. (B) male 67 y.o. same scale, contrast and luminosity parameters. Table 1. Correlations between dmB and ...
4
Flexural toughness as an attribute for impact damage evaluation of composite laminates
... Access and use of this website and the material on it are subject to the Terms and Conditions set forth at Flexural toughness as an attribute for impact damage evaluation of composite laminates Alemi-Ardakani, ...
9