• Aucun résultat trouvé

Deposition and fabrication

Design, fabrication, and characterization of an ultra-low cost inductively-coupled plasma chemical vapor deposition tool for micro- and nanofabrication

Design, fabrication, and characterization of an ultra-low cost inductively-coupled plasma chemical vapor deposition tool for micro- and nanofabrication

... The parameters measured for each sample were deposition rate, index of refraction, thickness uniformity, average film stress, and etch rate in 7:1 BOE. The methods [r] ...

235

Large scale fabrication of highly emissive nanodiamonds by chemical vapor deposition with controlled doping by SiV and GeV centers from a solid source

Large scale fabrication of highly emissive nanodiamonds by chemical vapor deposition with controlled doping by SiV and GeV centers from a solid source

... 0.7 and a closed-cycle cryostat ...chamber and cooled down to 10 ...fiber and sent to an avalanche photodiode (SPCL-AQRH-15 Excelitas Technologies) or to an optical spectrometer equipped a grating ...

21

Strained silicon-on-insulator - Fabrication and characterization

Strained silicon-on-insulator - Fabrication and characterization

... After deposition of an oxide layer (thickness 190 nm) the virtual substrates were implanted with hydrogen using 115 keV H 2 + ions with a dose of 3-5⋅10 16 cm -2 ...strength and to induce the layer ...

6

Design, fabrication, and characterization of a compact magnetron sputtering system for micro/nano fabrication

Design, fabrication, and characterization of a compact magnetron sputtering system for micro/nano fabrication

... This subsequently implies that for the same N2/Ar ratio setpoint as the target ages the deposition conditions shift more towards the sputter region creating more metallic [r] ...

228

Preparation and characterization of electroless deposition of Co-Fe-B thin films produced by electroless deposition

Preparation and characterization of electroless deposition of Co-Fe-B thin films produced by electroless deposition

... Electroless deposition has attracted interest since it constitutes a process to produce uniform deposits on sub- strates having irregular shapes and large ...electroless and electro- deposited Co–Fe ...

10

Chemical vapour deposition and atomic layer deposition of amorphous and nanocrystalline metallic coatings: towards deposition of multimetallic films

Chemical vapour deposition and atomic layer deposition of amorphous and nanocrystalline metallic coatings: towards deposition of multimetallic films

... CVD and ALD as alternative techniques to process metallic amorphous thin ...vapour deposition techniques can be used to provide films with higher purity, better conformality, and more versatility to ...

4

3D Bioprinting for Tissue and Organ Fabrication

3D Bioprinting for Tissue and Organ Fabrication

... derived and synthetic biomaterials have been developed to afford a spectrum of proper- ties, such as biocompatibility and appropriate physical assets, to ensure printability and long-term function- ...

17

Design and fabrication of a digitally reconfigurable surface

Design and fabrication of a digitally reconfigurable surface

... The digitally reconfigurable surface is a pin based mechanism for creating physical three- dimensional contoured surfaces from a computer aided design (CAD) input. When the digital design is properly downloaded into the ...

36

Design and fabrication of nanotweezers for nanomanipulation

Design and fabrication of nanotweezers for nanomanipulation

... Through proper design and matching of the actuator and the flexure mechanism pair, highly compliant arms with nanoscale resolution in motion can be achieved.... 2.2 [r] ...

139

Design and fabrication of quantum-dot lasers

Design and fabrication of quantum-dot lasers

... The most commonly fabricated semiconductor lasers are either gain-guided or index-guided whereby the difference between the two lasers is in the lateral confinement of [r] ...

89

Design, fabrication and control of soft robots

Design, fabrication and control of soft robots

... material and cause a desired ...extensible and adaptable, low-power soft ...generation, and a significant difference between the time constants for the generators and actuators, pressure ...

24

Deposition of granular solids

Deposition of granular solids

... Deposition of Granular Solids ...mixtures, and solutions that employ the COMSOL software ...the deposition of dry granular ...stresses, and to provide insights into the behavior of the ...

24

Fabrication and characterization of ionic conducting nanofibers

Fabrication and characterization of ionic conducting nanofibers

... However, it is important to note that the conductivities reported in this paper are only ‘‘apparent conductivities’’ since the formulas used to calculate the data are usually applied for bulk materials and not for ...

9

de la fabrication des compétences

de la fabrication des compétences

... L’archive ouverte pluridisciplinaire HAL, est destinée au dépôt et à la diffusion de documents scientifiques de niveau recherche, publiés ou non, émanant des établissements d’enseignemen[r] ...

16

Atmospheric transport and deposition of Indonesian volcanic emissions

Atmospheric transport and deposition of Indonesian volcanic emissions

... flux rate. We have addressed the question of the influence of meteorological conditions on volcanic plume SO 2 loss using an atmospheric chemistry model. We have exploited this technique to hold the modeled volcanic ...

14

Deposition of dense nanocrystalline Sm0.2Ce0.8O1.9 thin films by pulsed laser deposition

Deposition of dense nanocrystalline Sm0.2Ce0.8O1.9 thin films by pulsed laser deposition

... Ottawa ON, K1A OR6 Canada Samarium doped ceria (SDC) of composition Sm 0.20 Ce 0.80 O 1.90 is a promising electrolyte material for intermediate temperature solid oxide fuel cells (SOFCs) [1,2]. Compared to yttria ...

2

LA FABRICATION DES SIGNAUX

LA FABRICATION DES SIGNAUX

... bien fabrication : la technique, ici, inclut (exploite ?) le savoir (nous aurons à analyser leurs rapports), mais l’analyse technique n’en est pas pour autant ...

10

Assessment of airplane design, fabrication, and repair

Assessment of airplane design, fabrication, and repair

... In the case of airplane design, the load cases are broken into three categories, operating loads, limit loads, and ultimate loads.. Operating loads are the typical loads [r] ...

44

Deposition of tin oxide, iridium and iridium oxide films
by metal-organic chemical vapor deposition for electrochemical
wastewater treatment

Deposition of tin oxide, iridium and iridium oxide films by metal-organic chemical vapor deposition for electrochemical wastewater treatment

... 2.3 Deposition of Ir protective layer To improve the service life of specific SnO 2 electrode, the Ti substrate needs to be coated with a protective ...Ir deposition was studied in horizontal hot-wall CVD ...

9

Heavy-Chain Deposition Disease

Heavy-Chain Deposition Disease

... deposit and dissemination of sci- entific research documents, whether they are pub- lished or ...teaching and research institutions in France or abroad, or from public or private research ...

6

Show all 10000 documents...

Sujets connexes