• Aucun résultat trouvé

SERIES 200

N/A
N/A
Info
Télécharger
Protected

Academic year: 2022

Partager "SERIES 200"

Copied!
2
0
0

Chargement.... (Voir le texte intégral maintenant)

Texte intégral

(1)

HONEYWELL EDP

GENERAL SYSTEM:

SUBJECT:

SPECIAL INSTRUCTIONS:

DATE: May 15, 1966

8944 5566

Printed in U. S. A.

SOFTW ARE BULLETIN

SERIES 200

EASYTRAN SYMBOLIC TRANSLATOR BAND C

ADDENDUM #2

SERIES 200/ BASIC PROGRAMMING SYSTEM Changes to the Second Edition of the Reference Manual Easytran Sym.bolic Translator Band C, Order No. 035, dated Decem.ber, 1965.

These changes should be entered into the above referenced m.anual. They will be incorporated into future editions of the m.anual.

*

FILE NO.: 123. 1405.0000.0-035

*When ordering this publication, please specify Title and Underscored portion of File Number.

I I

J

i

(2)

ADDENDUM NO. 2 TO SERIES 200 REFERENCE MANUAL EASYTRAN SYMBOLIC TRANSLATOR BAND C

EASYTRAN CONTROL CARDS

The following information applies to Section III of the reference manual.

Page

3-3 :

Figure 3-3 should be replaced by the following corrected figure.

I II I . . . • 1 • t 10 II 1111 14 '1'1 IT 'I 1'lOa

"'

u'~~"""M"

• lIT.""

~

...

1'0 ... IINa' • • " . " • • IC IIU . . . . . . " . . . . 10 11 n" 1411",",,,,, 10

ATOEC I prOO·

iden.

Page 3-5 Page 3-5

blank II I IliA I blank tapt tape tape tape tape tape blank

22 2H unit unit unit unit unit unit

#1 #2 #3 #4 #5 #6

Figure 3-3. Easytran 1401 Control Card

Under the heading "Card Column," 29-35 should be changed to 30-35.

Immediately preceding 30-35. insert the following description for card column 29:

1 = Object program is to be run on the Model 120 with the Type 123 Card Reader and the Type 214-1 Card Punch corrected to the Integrated Control Unit.

Blank = Object program is to be run on the Model 200 or the Model 120 without the Type 123 Card Reader and the Type 214-1 Card Punch.

EASYTRAN SYMBOLIC TRANSLATOR B OPERATION

The following information applies to Section VII of the reference manual.

Page 7-8 :

Page 7-9 : Page 7-10:

Page 7-11:

Page 7-12:

Page 7-12:

Page 7-13:

Delete the last sentence of step 8, which reads as follows: "Readdress the physical tape drive as logical

4:"

In Figure 7-3, change the designations of two work tapes from 4 to O.

In Figure 7-4, change the designations of two work tapes from 4 to O.

Delete the last sentence of step 9 and step 6.

f

In Figure 7-5, change the designation of one work tape from 4 to O.

Delete the last sentence of step 6.

In Figure 7-6, change the designations of two work tapes from 4 to O.

1

Références

Télécharger maintenant ( PDF - 2 Page - 58.74 KB )

Documents relatifs

SERIES 200

If it begins in column 9, the tag is as- signed to the location at which the next instruction would have begun had the MORG statement not been present (seethe example

SERIES 200

However, it should be noted that the maximum number of alphanumeric characters which can be contained in the constant depends on the number of card columns

SERIES 200

The remaining octal variant is the character that defines the size of the information units involved in the operation, as described in Table 8-17 of the reference

SERIES 200

This program has been checked but no guarantee is expressed or implied to the user concerning its functioning. Honeywell Will cooperate in making functional

'SERIES 200

The binary state of the six CONTROL push- button indicators display the octal address of a control memory register. The display does not change while the

SERIES 200

1. Obtain descriptive information about the program, e. g., memory requirements, number of segments, program listing, pertinent operating procedures. Prepare an Easytran

SERIES 200

schedule summary. Execution included supervised performance of the prepared program schedule by a small monitor which sequenced programs and informed the operator of

SERIES 200

A singl~ tape write instruction causes the central processor to transfer data from a specified output area in main memory, on a character-by-character basis, to